FCC-B Radio Frequency Interference Statement This equipment has been tested and found to comply with the limits for a class B digital device, pursuant to part 15 of the FCC rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instruction manual, may cause harmful interference to radio communications.
Safety Instructions Always read the safety instructions carefully. Keep this equipment away from humidity. Lay this equipment on a reliable flat surface before setting it up. The openings on the enclosure are for air convection hence protects the equipment from overheating. DO NOT COVER THE OPENINGS. Confirm the voltage of the power source and adjust accordingly to 115/230V before connecting the equipment to the power inlet.
WEEE Statement (Waste Electrical and Electronic Equipment) The WEEE directive places an obligation on EU-based manufacturers, distributors, retailers and importers to take-back electronics products at the end of their useful life. A sister Directive, ROHS (Restriction of Hazardous Substances) compliments the WEEE Directive by banning the presence of specific hazardous substances in the products at the design phase.
TABLE OF CONTENTS FCC-B Radio Frequency Interference Statement............. i Trademarks ........................i Safety Instructions......................ii WEEE Statement ......................iii Introduction ........................6 iONE-GX31 Series Specifications ................... 6 Processor Support......................6 Chipset ......................... 6 Memory Support......................6 Networking ........................6 Audio ..........................6 Hard Disk Drive ......................
Page 6
Installing the Memory Module DDR2 SODIMM ............21 Installing the Hard Disk Drive ..................22 Installing the Optical Disk Drive.................. 23 Installing the Mini-PCI / PCIE Card (Optional)............25 Installing the IrDA Module (Optional)................26 Installing the Cover..................... 27...
Introduction Congratulations for purchasing the iONE-GX31. The iONE-GX31 Series is your best Slim LCD PC choice. With the fantastic appearance and small form factor, it can easily be set anywhere. The feature packed platform also gives you an exciting PC experience.
4 TV Tuner ports - - Optional with TV Tuner (COAX Cable In, RCA Composite Video In, Audio Left & Audio Right) 1 Reset button 1 CMOS clear button Power Supply 180 Watt Power Adapter 110/230 Volt Switching Dimensions 47.5cm (H) x 43cm (W) x 25.5cm (D) (with stand) Cybernet iONE-GX31 Product Orientation Page 7...
Also functions as Exit button in the Menu Mode. Menu/Enter Press once to get to On-Screen display Mode to allow various adjustments as listed below. Also functions as the Enter or Select button in Menu Mode. Cybernet iONE-GX31 Product Orientation Page 11...
Select to adjust “Red” Select to adjust “Green” Select to adjust “Blue” At the Bottom: Exit Select to Exit the On Screen Display (Will exit automatically if untouched). → Select to Reset all LCD Display settings. Cybernet iONE-GX31 Product Orientation Page 12...
Page 15
Figure 11: System Ventilation Fan Figure 12, 13 and 14: Heat Sink Ventilation, More System Ventilation and Stand Cybernet iONE-GX31 Product Orientation Page 14...
Forceps/tweezers can be used to pick up tiny screws or set up the jumpers. Rubber gloves can prevent injury from static charge. Electric screwdriver can be used to secure all screws more quickly. Cybernet iONE-GX31 System Assembly Page 15...
Orientation of Key Parts Figures 15,16,17,18 and 19: System Fan and Ventilation, HDD and Optical Drive, Heat Sink, Memory Modules, Mini-PCI/PCIe and Touch Panel Control. Cybernet iONE-GX31 System Assembly Page 16...
First lift the metal shield and slide it to the right clearing the optical drive door (at the top right) then disconnect the system fan cable connector from the motherboard at FAN2 next to the top right corner of the CPU. Cybernet iONE-GX31 System Assembly Page 17...
This should remain in place until actually installing a CPU. 2. Remove the plastic cap to reveal the socket pins. Note: Do not touch the socket pins to avoid damaging. 3. Open the cover. Cybernet iONE-GX31 System Assembly Page 18...
Page 20
CPU with vertical motion and reinstall. 5. Close the cover and the lever to complete the installation. Please note that any violation of the correct installation procedures may cause permanent damage to your mainboard. Cybernet iONE-GX31 System Assembly Page 19...
Note: Do not fix any screws until the four screws are in their positions. 3. Secure the two screws at the opposite end near the top edge of the bezel. 4. Connect the power cable to CPU Fan on the mainboard labeled FAN 1 CUP FAN. Cybernet iONE-GX31 System Assembly Page 20...
3. Press the memory module down and the metal clip at each side of the DIMM slot will automatically close. 4. Repeat the steps to install another memory module to meet your needs. Cybernet iONE-GX31 System Assembly Page 21...
4. Connect the SATA cable. 5. Connect the power cable. Replace the Optical Disk Drive securing the four screws (two screws on the top, two screws on the side) to secure the HDD and complete the installation. Cybernet iONE-GX31 System Assembly Page 22...
2. Secure the two screws on the ODD interface board. 3. Put the ODD on the ODD frame and line up the four screw holes accordingly. 4. Secure the four screws on the ODD frame. Cybernet iONE-GX31 System Assembly Page 23...
Page 25
Hard Disk Drive slot. 7. Secure the four screws to fix the ODD frame and complete the installation. Cybernet iONE-GX31 System Assembly Page 24...
PCIE slot at a 45° angle. Then push it in until the golden finger on the mini-PCIE card is deeply inserted in the mini-PCIE slot. 4. Press down the mini-PCIE card and secure the screw to complete the installation. Cybernet iONE-GX31 System Assembly Page 25...
FP board. 4. Connect the cable IR to J1 on the FP board and connect the audio cable from J2 on the FP board to J7 on the Mainboard to complete the installation. Cybernet iONE-GX31 System Assembly Page 26...
1. Connect the power cable to System Fan on the mainboard before securing the metal cover with seventeen screws. 2. Secure the plastic cover with eleven screws. 3. Secure the stand with four screws. Cybernet iONE-GX31 System Assembly Page 27...
Page 29
Cybernet iONE-GX31 System Assembly Page 28...